Apple iPhone 6 | Silver | 32GB | Refurbished | Grade A+ |

Brand name of the company that manufactures the device.

Model name of the device.

Аlternative names, under which the model is known.

Information about the width, i.e. the horizontal side of the device when it is used in its standard orientation.

Information about the height, i.e. the vertical side of the device when it is used in its standard orientation.

Information about the thickness/depth of the device in different measurement units.

Information about the weight of the device in different measurement units.

Estimated volume of the device, calculated from the dimensions provided by the manufacturer. Applies for devices in the form of a rectangular parallelepiped.

Information about the colors, in which the device is available in the market.

Materials used in the fabrication of the device's body.

Information about the type and size (form factor) of the SIM card used in the device.

Information about the number of SIM cards, supported by the device.

GSM (Global System for Mobile Communications) was developed to replace the analog cellular network (1G), therefore it is referred to as a 2G mobile network. It has been improved with the addition of General Packet Radio Services (GPRS) and later via the Enhanced Data rates for GSM Evolution (EDGE) technology.

CDMA (Code-Division Multiple Access) is a channel access method for communications within mobile networks. Compared to other 2G and 2.5G standards like GSM and TDMA, it provides increased data transfer speeds and allows more subscribers to connect simultaneously to the network.

CDMA2000 is a family of 3G standards for mobile networks based on CDMA and providing high-quality voice and broadband data services over wireless networks. Its advantages include stronger signal, fewer drop-offs and breakups, analog capabilities, very high spectral capacity, etc.

TD-SCDMA (Time Division Synchronous Code Division Multiple Access) is a 3G standard for mobile networks. It is developed as an alternative to the W-CDMA standard in China by the Chinese Academy of Telecomunications Technology, Datang Telecom and Siemens AG, and combines TDMA and CDMA.

UMTS stands for Universal Mobile Telecommunications System. Based on the GSM standard, it is deemed as a 3G mobile network standard. It has been developed by the 3GPP and its major advantage is the provision of greater bandwidth and spectral efficiency, due to the W-CDMA technology.

LTE is deemed to be the fourth generation (4G) of mobile communications technology. It has been developed by the 3GPP based on the GSM/EDGE and UMTS/HSPA technologies in order to increase the speed and capacity of wireless data networks. A further development of the technology is called LTE Advanced.

There are several network technologies that enhance the performance of mobile networks mainly by increased data bandwidth. Information about the communication technologies supported by the device and their respective uplink and downlink bandwidth.

Information about the operating system used by the device as well as its version.

The SoC integrates different hardware components such as the CPU, GPU, memory, peripherals, interfaces, etc., as well as software for their functioning.

Information about the process technology used in manufacturing the chip. The value in nanometers represents half the distance between elements that make up the CPU.

CPU is the Central Processing Unit or the processor of a mobile device. Its main function is to interpret and execute instructions contained in software applications.

The CPU bits are determined by the bit-size of the processor registers, address buses and data buses. 64-bit CPUs provide better performance than 32-bit ones, which on their part perform better than 16-bit processors.

The instruction set architecture (ISA) is a set of commands used by the software to manage the CPU's work. Information about the set of instructions the processor can execute.

The cache memory is used by the processor in order to shorten the time needed to access data and instructions that a frequently used. The L1 (level 1) cache memory has a small volume, but operates faster than the RAM and the rest cache memory levels. If the processor does not find the data needed in L1, it continues to look for it in the L2 cache memory. In some processors the search in L1 and L2 is simultaneous.

The L2 (level 2) cache memory is slower than L1, but has a larger capacity, instead, which allows it to cache more data. Just like L1, it is much faster than the system memory (RAM). If the CPU does not find the data needed in L2, it proceeds to look for them in the L3 cache memory (if there is such) or in the RAM.

The L3 (level 3) cache memory is slower than L2, but has a larger capacity, instead, which allows it to cache more data. Just like L2, it is much faster than the system memory (RAM).

A CPU core is the processor unit, which executes software instructions. Presently, besides single-core processors, there are dual-core, quad-core, hexa-core and so on multi-core processors. They increase the performance of the device allowing the execution of multiple instructions in parallel.

The frequency of the processor describes its clock rate in cycles per second. It is measured in Megahertz (MHz) or Gigahertz (GHz).

GPU is a graphical processing unit, which handles computation for 2D/3D graphics applications. In mobile devices GPU is usually utilized by games, UI, video playback, etc. GPU can also perform computation in applications traditionally handled by the CPU.

Similar to the CPU, the GPU consists of processing units called cores. They handle the computation of graphics in various applications.

RAM (Random-Access Memory) is used by the operating system and all installed applications. Data in the RAM is lost after the device is turned off or restarted.

Information about the type of RAM used by the device.

Information about the capacity of the built-in storage of the device. Sometimes one and the same model may is offered in variants with different internal storage capacity.

One of the main characteristics of the display is its type/technology, on which depends its performance.

In mobile devices display size is represented by the length of its diagonal measured in inches.

Approximate width of the display

Approximate height of the display

The ratio between the long and the short side of the display

The display resolution shows the number of pixels on the horizontal and vertical side of the screen. The higher the resolution is, the greater the detail of the displayed content.

Information about the number of pixels per centimeter (ppcm) or per inch (ppi) of the display. The higher the pixel density, the more detailed and clearer is the information displayed on the screen.

The color depth of the display is also known as bit depth. It shows the number of bits used for the color components of one pixel. Information about the maximum number of colors the screen can display.

The estimated percentage of the screen area from the device's front area.

Information about other functions and features of the display.

Sensors vary in type and purpose. They increase the overall functionality of the device, in which they are integrated.

Information about the manufacturer and the model of the image sensor used by the camera of the device.

Digital cameras use image sensors for taking photos. The sensor characteristics are some of the main factors determining the quality of the camera integrated in the mobile device.

Information about the dimensions of the image sensor used in the device. Usually cameras with larger sensors and less pixel density tend to provide better image quality despite the lower resolution.

A smaller pixel size allows the image sensor to use more pixels thus providing better image resolution. On the other hand, this may negatively impact noise levels and decrease image quality at high ISO settings.

Crop factor is the ratio of the dimensions of a full frame camera's sensor (36 x 24 mm, which equals the frame size of a 35 mm film) and the dimensions of the image sensor of the device. The number shown is the ratio between the diagonals of a full frame sensor (43.3 mm) and the device sensor.

ISO rating indicates the light sensitivity of the image sensor. The lower the number, the less sensitive to light the image sensor is and vice versa - higher ISO ratings indicate higher sensitivity and ability of the image sensor to work better in low light conditions.

Aperture (f-stop number) indicates the size of the lens diaphragm opening, which controls the amount of light reaching the image sensor. The lower the f-stop number, the larger the diaphragm opening is.

Focal length is the distance in millimeters from the focal point of the image sensor to the optical center of the lens. A focal length, which results in the same field of view on a full-frame (35 mm) camera, is also provided.

Cameras of mobile devices use mainly a LED or a Xenon flash. The LED flash has a softer burst of light and in contrast to the much brighter Xenon flash, is used for recording videos as well.

One of the main characteristics of the cameras of mobile devices is their resolution, which shows the number of pixels on the horizontal and vertical dimensions of the image.

Information about the maximum resolution available for shooting a video with the device.

Information about the maximum number of frames per second (fps), supported by the device while recording a video at maximum resolution. Some of the main standard frame rates for recording and playing video are 24p, 25p, 30p, 60p.

Information about additional software and hardware features of the privamery camera, which improve its overall performance.

Digital cameras use image sensors for taking photos. The sensor characteristics are some of the main factors determining the quality of the camera integrated in the mobile device.

Aperture (f-stop number) indicates the size of the lens diaphragm opening, which controls the amount of light reaching the image sensor. The lower the f-stop number, the larger the diaphragm opening is.

Information about the maximum image resolution of the secondary camera. Often, the resolution of the secondary camera is lower than the one of the primary camera.

Information about the maximum resolution available for shooting a video by the secondary camera.

Information about the maximum number of frames per second (fps), supported by the secondary camera while recording a video at maximum resolution.

The loudspeaker is a device, which reproduces various sounds such as ring tones, alarms, music, voice calls, etc. Information about the type of speakers the device uses.

Information whether the device has an FM radio receiver or not.

The tracking/positioning service is provided by various satellite navigation systems, which track the autonomous geo-spatial positioning of the device that supports them. The most common satellite navigation systems are the GPS and the GLONASS. There are also non-satellite technologies for locating mobile devices such as the Enhanced Observed Time Difference, Enhanced 911, GSM Cell ID.

Wi-Fi communication between devices is realized via the IEEE 802.11 standards. Some devices have the possibility to serve as Wi-Fi Hotspots by providing internet access for other nearby devices. Wi-Fi Direct (Wi-Fi P2P) is another useful standard that allows devices to communicate with each other without the need for wireless access point (WAP).

The technology has several versions, which improve the connection speed, range, connectivity and discoverability of the devices. Information about the Bluetooth version of the device.

Bluetooth uses various profiles and protocols related to faster exchange of data, energy saving, better device discoverability, etc. Some of those supported by the device are listed here.

There are several versions of the Universal Serial Bus (USB) standard: USB 1.0 (1996), the USB 2.0 (2000), the USB 3.0 (2008), etc. With each following version the rate of data transfer is increased.

Тhe USB interface in mobile devices may be used for different purposes such as battery charging, using the device as a mass storage, host, etc.

Information whether the device is equipped with a 3.5 mm audio jack.

Information about some of the most widely used connectivity technologies supported by the device.

Information about some of the features and standards supported by the browser of the device.

List of some of the most common audio file formats and codecs supported standardly by the device.

List of some of the most common video file formats and codecs supported standardly by the device.

The capacity of a battery shows the maximum charge, which it can store, measured in mili-Ampere hours.

The battery type is determined by its structure and more specifically, by the chemicals used in it. There are different battery types and some of the most commonly used in mobile devices are the lithium-ion (Li-Ion) and the lithium-ion polymer battery (Li-Polymer).

2G talk time is the time period a battery charge will last, if one is constantly talking on the phone in a 2G cellular network.

2G stand-by time is the longest time a battery charge will last, if the device is not used but is constantly connected to the 2G cellular network.

3G talk time is the time period a battery charge will last, if one is constantly talking on the phone in a 3G cellular network.

3G stand-by time is the longest time a battery charge will last, if the device is not used but is constantly connected to the 3G mobile network.

Information about some additional features of the device's battery.

The SAR head rating shows the highest level of exposure to electromagnetic radiation measured when the device is held next to the ear in a talk position. In Europe, the SAR limit for hand-held mobile devices is set to 2 W/kg per 10 g of tissue. This standard is specified by the CENELEC, complies with the IEC standards and follows the ICNIRP Guidelines 1998.

This SAR rating shows the highest level of exposure to electromagnetic radiation measured when the device is placed at the hip level. The top SAR value for mobile devices used in Europe is limited to 2 W/kg per 10 g of tissue. This standard follows the ICNIRP Guidelines 1998 as well as the IEC standards and is determined by the CENELEC.

This SAR rating shows the maximum level of exposure to electromagnetic radiation taken when the device is placed next to the ear. The applicable limit for the US is 1.6 W/kg per 1 g of tissue. In the US the FCC tests and sets the SAR limits for all mobile devices, which are controlled by the CTIA.

The SAR body rating shows the maximum level of exposure to electromagnetic radiation when the device is positioned against the body at the hip. The highest SAR value of mobile devices allowed in the US is set to 1.6 W/kg per 1 g of tissue. It is specified by the FCC and the CTIA follows whether the mobile devices comply with this standard.